FIXME **Diese Seite wurde noch nicht vollständig übersetzt. Bitte helfen Sie bei der Übersetzung.**\\ //(diesen Absatz entfernen, wenn die Übersetzung abgeschlossen wurde)//

====== Hyper-V (VM) ======

<WRAP center round tip 100%>

== Vorbereitungen durchgeführt? ==

Lese Dir zuerst die → [[installation_von_loxberry:die_installation_von_loxberry:start|Anleitung zur Vorbereitung]] durch!

</WRAP>

%%The archive contains the DietPi %%''README.md''%%, the %%''.vhdx''%% virtual disk image and a %%''hash.txt''%%, which contains hashes to check the integrity of the virtual disk image. Move the %%''.vhdx''%% file to the desired virtual machine folder on your harddisk.%%

==== Add a Hyper-V virtual machine ====

Next, a Hyper-V machine needs to be created. Start the Hyper-V-Manager, right click on your PCs node in the left tree and open the dialog wizard for the machine generation (“New” -> “Virtual Machine”):

{{https://dietpi.com/docs/assets/images/dietpi-HyperV-VM-generation.png?450x364|Hyper-V machine generation}}

In the following wizard you have to set the following:

  - Give your machine a name (“Specify Name and Location”)
  - Select the Hyper-V Generation: Select%% %%**Generation 1**%% %%(“Specify Generation”)
  - Choose your RAM size (e.g. 2048 MB)
  - If you have already configured a network, select your network. Otherwise let it “Not connected” and change it afterwards
  - Choose to use the extracted%% %%''.vhdx''%% %%Hyper-V disc file (see above)

If you have not set up any network connection, go on with the%% %%**Virtual Switch Manager**%% %%and add a network. Select that network in your virtual machine settings afterwards.

{{https://dietpi.com/docs/assets/images/dietpi-HyperV-manage-network.png?250x284|Hyper-V network management}}

==== First boot of the new Hyper-V machine ====

First, click on%% %%**//Connect//**%% %%to open a window of the virtual machine:

{{https://dietpi.com/docs/assets/images/dietpi-HyperV-connect-machine.png?450x205|Hyper-V machine connection}}

Then press%% %%**//Start//**%% %%to boot up the machine:

{{https://dietpi.com/docs/assets/images/dietpi-HyperV-start-machine.png?550x420|Hyper-V machine start}}

After this, your machine should boot up.

<WRAP center round important 100%>

== You must disable IPv6 when the host uses WiFi ==

Sometimes the VM has difficulties to connect to the internet. This is reported in a network bridged mode and when the host connects to the internet via WiFi: In these cases the IPv6 routing between the VM and the internet fails (e.g. see%% %%there).\\ A typical result is, that the system does not find the update server (e.g. at the very first update run). This is then signaled during the “apt update” procedure of the first boot startup.\\ To overcome this, open a subshell (or an additional ssh window), start%% %%''dietpi-config''%% %%and disable%% %%**IPv6**%% %%within the Network options.

{{https://dietpi.com/docs/assets/images/dietpi-VirtualBox-IPv6.png?500x225|IPv6 deactivate screenshot}}

Then exit%% %%''dietpi-config''. After this the first time installer procedure should run again from the start.

</WRAP>

==== Additional information / troubleshooting ====

=== Network connection not found ===

In the case that you did not setup your network configuration properly, the booting procedure will not find a network connection and may respond with this boot console output:

{{https://dietpi.com/docs/assets/images/dietpi-HyperV-boot-wo-network.jpg?722x164|Hyper-V boot without network}}

Then you have to check and repair your network configuration within the%% %%**Virtual Switch Manager**.

=== Generate a Hyper-V Generation 2 machine ===

An option to get a Hyper-V Generation 2 machine is to generate your own Hyper-V image via a%% %%**Debian network installation**%% %%(booting the Hyper-V machine from a Debian%% %%''netinst.iso''%% %%installer like you would do it on a PC). Install a minimal Debian machine (i.e. no X11 desktops, etc.). Afterwards run the procedure described in section%% %%“Make your own distribution”. Generation 2 machines support (and require) to boot in UEFI mode, support%% %%Secure Boot,%% %%TPM, use modern SCSI controllers and have higher hardware limits. For use as a home server, however, you will not need any of these functions.

====== Weiter mit der LoxBerry Installation ======

→ [[installation_von_loxberry:die_installation_von_loxberry:start#diet_pi_erstkonfiguration|Nun geht es hier weiter mit der DietPi Erstkonfiguration]]