Metainformationen zur Seite

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen RevisionVorhergehende Überarbeitung
Nächste Überarbeitung		Vorhergehende Überarbeitung
installation_von_loxberry:die_installation_von_loxberry:native-pc [2023/03/16 10:22] – Michael Schlenstedtinstallation_von_loxberry:die_installation_von_loxberry:native-pc [2024/01/01 18:54] (aktuell) – Michael Schlenstedt
Zeile 5: Zeile 5:
 <WRAP center round tip 100%> <WRAP center round tip 100%>
  
-== Grundinstallation durchgeführt? ==+== Vorbereitungen durchgeführt? ==
  
-Lese Dir zuerst die → [[installation_von_loxberry:die_installation_von_loxberry:start|Anleitung zur Grundinstallation]] durch!+Lese Dir zuerst die → [[installation_von_loxberry:die_installation_von_loxberry:start|Anleitung zur Vorbereitung]] durch!
  
 </WRAP> </WRAP>
 +
 +\\ \\
  
 <WRAP center round help 100%> <WRAP center round help 100%>
 +
 == UEFI or BIOS? == == UEFI or BIOS? ==
  
Zeile 17: Zeile 20:
  
 In case of an UEFI based PC see the “UEFI Installer image” tab. In case of a BIOS based PC see the “BIOS Installer image” tab or “BIOS direct write image” tab. “BIOS Installer image” or “BIOS direct write image”? In case of an UEFI based PC see the “UEFI Installer image” tab. In case of a BIOS based PC see the “BIOS Installer image” tab or “BIOS direct write image” tab. “BIOS Installer image” or “BIOS direct write image”?
 +
 </WRAP> </WRAP>
  
 <WRAP center round help 100%> <WRAP center round help 100%>
 +
 == “BIOS Installer image” or “BIOS direct write image”? == == “BIOS Installer image” or “BIOS direct write image”? ==
  
 The “BIOS installer image” is used to boot from and install the DietPi system on a different target boot drive (storage medium). In contrary to that the “BIOS direct write image” is used to be write the image directly to the target DietPi boot drive. The “BIOS installer image” is used to boot from and install the DietPi system on a different target boot drive (storage medium). In contrary to that the “BIOS direct write image” is used to be write the image directly to the target DietPi boot drive.
 +
 </WRAP> </WRAP>
  
-===== UEFI Installer Image =====+====== UEFI Installer Image / BIOS installer image ======
  
 Download%% %%[[https://rufus.ie/|Rufus]]%% %%and run the application. There is a portable version of Rufus available which doesn’t require any local installation. Download%% %%[[https://rufus.ie/|Rufus]]%% %%and run the application. There is a portable version of Rufus available which doesn’t require any local installation.
  
 <WRAP center round important 100%> <WRAP center round important 100%>
 +
 == Be careful if you run alternative applications! == == Be careful if you run alternative applications! ==
  
 While%% %%Balena Etcher%% %%is recommended for installing DietPi on SBCs, it does not provide good results for UEFI images. The same also with win32diskimager, which does not work as an alternative. While%% %%Balena Etcher%% %%is recommended for installing DietPi on SBCs, it does not provide good results for UEFI images. The same also with win32diskimager, which does not work as an alternative.
 +
 </WRAP> </WRAP>
- 
  
 ==== Write image to USB drive ==== ==== Write image to USB drive ====
  
-Start%% %%Rufus%% %%application and make sure you have your USB drive inserted into your computer. Follow the next steps:+Start%% %%[[https://rufus.ie/|Rufus]]%% %%application and make sure you have your USB drive inserted into your computer. Follow the next steps:
  
   - Select the USB device   - Select the USB device
Zeile 59: Zeile 66:
  
 <WRAP center round important 100%> <WRAP center round important 100%>
 +
 == BIOS settings == == BIOS settings ==
  
-It may be necessary to change BIOS settings to enable the UEFI boot. This action is not described here.+It may be necessary to change BIOS settings to enable the UEFI boot or USB stick boot. This action is not described here. 
 </WRAP> </WRAP>
  
Zeile 92: Zeile 101:
 These steps take some time, be patient! Otherwise buy an SSD. ::-)At the end the system executes a shutdown. These steps take some time, be patient! Otherwise buy an SSD. ::-)At the end the system executes a shutdown.
  
-<WRAP center round important 60%>+<WRAP center round tip 100%> 
 == WiFi connection == == WiFi connection ==
  
Zeile 100: Zeile 110:
   - In the same file%% %%''dietpi-wifi.txt'', set%% %%''aWIFI_KEY[0]''%% %%to the password of your WiFi network.   - In the same file%% %%''dietpi-wifi.txt'', set%% %%''aWIFI_KEY[0]''%% %%to the password of your WiFi network.
   - Save and close the files   - Save and close the files
 +
 </WRAP> </WRAP>
  
Zeile 105: Zeile 116:
  
 For the first boot up of your PC disconnect your USB stick from the target PC and power on the PC to login and execute the first boot procedure. For the first boot up of your PC disconnect your USB stick from the target PC and power on the PC to login and execute the first boot procedure.
 +
 +====== Bios direct write Image ======
 +
 +Download%% %%[[https://rufus.ie/|Rufus]]%% %%and run the application. There is a portable version of Rufus available which doesn’t require any local installation.
 +
 +<WRAP center round important 100%>
 +
 +== Be careful if you run alternative applications! ==
 +
 +While%% %%Balena Etcher%% %%is recommended for installing DietPi on SBCs, it does not provide good results for UEFI images. The same also with win32diskimager, which does not work as an alternative.
 +
 +</WRAP>
 +
 +==== Write image to disc drive ====
 +
 +Start%% %%[[https://rufus.ie/|Rufus]]%% %%application and make sure you have your disc drive connected into your computer. This may e.g. be done using an USB to SATA controller if you use a SATA disc drive. Follow the next steps:
 +
 +  - Show advanced drive properties and select%% %%**List USB hard drives**\\ (in case that you have connected your disc drive via a USB adapter)
 +  - Select the disc drive device
 +  - Select the downloaded%% %%**DietPi**%% %%image
 +  - Click on%% %%**Start**%% %%button
 +
 +Ensure that the selected disc drive is the correct one.
 +
 +<WRAP center round important 100%>
 +
 +== All data on the disc drive will be erased! ==
 +
 +Before starting the installation first make a backup of the data available on the disc drive if you need it later again!
 +
 +</WRAP>
 +
 +{{https://dietpi.com/docs/assets/images/dietpi-rufus-bios-direct-write-image.png?474x607|Rufus BIOS direct write image selections screenshot}}
 +
 +==== Boot the target PC ====
 +
 +<WRAP center round tip 100%>
 +
 +== WiFi connection ==
 +
 +To setup the WiFi, you have to change the network settings matching to your environment:
 +
 +  - Open the file%% %%''dietpi-wifi.txt''%% %%and set%% %%''aWIFI_SSID[0]''%% %%to the name of your WiFi network.
 +  - In the same file%% %%''dietpi-wifi.txt'', set%% %%''aWIFI_KEY[0]''%% %%to the password of your WiFi network.
 +  - Save and close the files
 +
 +</WRAP>
 +
 +You need to set these values before you boot up the PC for the first time (initial boot).
 +
 +For the first boot up of your PC disconnect your disc drive from your working PC and connect it to the target PC. Then power on the target PC to login and execute the first boot procedure.
  
 ====== Weiter mit der LoxBerry Installation ====== ====== Weiter mit der LoxBerry Installation ======
  
-→ [[installation_von_loxberry:die_installation_von_loxberry:start#diet_pi_erstkonfiguration|Nun geht es hier weiter mit der LoxBerry Installation.]]+→ [[installation_von_loxberry:die_installation_von_loxberry:start#diet_pi_erstkonfiguration|Nun geht es hier weiter mit der DietPi Erstkonfiguration]]